Most businesses ordering branded uniforms, sports kits, or promotional merchandise in Kenya judge a sublimation print by how it looks on delivery. Very few ask the question that determines that result: What heat press settings did the supplier use to produce it?
Temperature, time, and pressure are the three variables that control every dye sublimation print. Getting any one of them wrong produces a defective result — faded colour, ghosting, scorched fabric, or branding that fails after the first wash. Getting all three right, consistently, across every job, is what separates a dye sublimation expert from a general print shop that happens to own a heat press.
This guide explains what each variable controls, what correct settings look like, and what questions to ask any sublimation supplier in Kenya before placing a bulk order. Waves Branding produces all dye sublimation orders in-house at our Keekorok Road, Nairobi CBD facility, under process controls that meet these standards on every job.
Why Process Settings Matter for Print Quality
Dye sublimation is not a forgiving process. Unlike screen printing or vinyl cutting, where errors are often visible before the job leaves the press, sublimation defects only reveal themselves after the transfer paper is peeled back — by which point the substrate has already been exposed to heat, and the result is permanent.
A supplier who presses at the wrong temperature will deliver prints that appear acceptable until the first wash, at which point the colour fades significantly because the ink never fully bonded with the fibres. A supplier who uses insufficient pressure will deliver prints with uneven colour density — visible as lighter patches or streaking across the design. A supplier who underestimates time will produce ghosting: a faint double image caused by the transfer paper shifting fractionally during press.

None of these defects can be corrected after production. They require a complete reprint.
For procurement managers ordering corporate uniforms, staff workwear, or branded sports kits in Kenya, this means the supplier’s process capability is a direct financial risk. A technically correct sublimation press eliminates these risks entirely. Understanding the correct settings gives you the ability to assess a supplier’s competence before you place the order — not after you receive a defective batch.
Temperature (180–200°C): What It Controls
Temperature is the primary variable in dye sublimation. Heat drives the phase transition that makes the process work: at sufficient temperature, sublimation inks convert from solid to gas, penetrate the open polyester fibres, and bond permanently as the material cools.
Correct range: 180–200°C
The specific temperature within this range is adjusted based on:
- Fabric weight (GSM): Heavier fabrics (e.g. 240 GSM overalls fabric) require temperatures at the higher end of the range to ensure complete ink penetration through the full fabric depth. Lightweight flag fabric (80–100 GSM) requires lower temperatures to avoid scorching.
- Fabric composition: 100% polyester tolerates the full temperature range. Polyester-cotton blends require more careful calibration — too high a temperature risks scorching the cotton fibres and producing a burnt smell or discolouration.
- Substrate type: Polymer-coated hard surfaces (mugs, plaques, phone cases) have specific temperature requirements that differ from fabric — typically 180–190°C for most coated ceramics.
What happens at incorrect temperatures:
| Temperature | Effect on print |
|---|---|
| Below 175°C | Incomplete ink conversion — faded, washed-out print that deteriorates further after laundering |
| 180–200°C (correct) | Full ink-to-gas conversion, complete fibre penetration, wash-permanent bond |
| Above 205°C | Fabric scorching on lightweight fabrics; colour shift on heat-sensitive polyester blends; potential structural damage to fabric |
A supplier who cannot state their temperature setting for your specific fabric type is not calibrating their process to your order. They are using a single default setting for all jobs — a significant quality risk for buyers ordering across multiple product types.
Time (30–60 Seconds): What It Controls
Dwell time — the duration the substrate remains under heat and pressure — controls how completely the sublimation ink penetrates the fabric fibres. Insufficient time produces partial bonding; excessive time risks scorching, colour shift, and fabric damage.
Correct range: 30–60 seconds
Dwell time is adjusted in conjunction with temperature:
- Short dwell (30–35 seconds): Used with higher temperatures on lightweight fabrics (flags, lightweight jerseys, banner fabric). Shorter exposure at higher heat achieves full penetration without risking fabric damage.
- Standard dwell (40–50 seconds): The baseline for most corporate uniform garments — polo shirts, dust coats, and reflective vests in standard polyester weights.
- Longer dwell (55–60 seconds): Used for heavier fabrics (240+ GSM overalls and workwear) and for polymer-coated hard substrates (mugs, plates) where deeper penetration is required.
What ghosting looks like — and why it happens: Ghosting is a faint duplicate image visible alongside the primary design, typically offset by 1–3mm. It is caused by the transfer paper shifting during or immediately after pressing, before the ink has fully solidified in the fabric. It is prevented by ensuring correct pressure holds the paper in place throughout the dwell period and by allowing the substrate to cool slightly before peeling.
A supplier who rushes the peeling step to increase throughput is a common source of ghosting defects on bulk orders. On a 500-piece corporate uniform order, ghosting discovered on delivery means a full reprint.
Pressure: What Happens When Pressure Is Wrong
Pressure is the least-discussed variable in dye sublimation — and the most common source of uneven print quality on large-format jobs (flags, backdrops, wide fabric banners).
Correct setting: medium-firm, applied evenly across the entire transfer area
Pressure is not typically expressed in precise PSI values for fabric sublimation — it is calibrated by the equipment operator based on the substrate and confirmed through test press results. The critical requirement is consistency across the full surface of the transfer. Any variation in pressure produces a variation in ink density in the finished print.

Effects of incorrect pressure:
- Too low: Insufficient contact between transfer paper and fabric — produces lighter areas, streaking, and incomplete colour coverage. Common on wide-format flag jobs where the press bed does not fully contact the edges of large pieces.
- Uneven: The most frequent defect. Visible as gradients or patches across the print, where some areas are fully saturated, and others are lighter. Often caused by a worn or uneven press bed, or by incorrect loading of oversized substrates.
- Too high: Compression of the fabric fibres, particularly on thicker materials. Can flatten the fabric texture and, on polyester-cotton blends, cause permanent texture change.
For wide-format sublimation jobs — flags, gazebo canopies, fabric backdrops — a supplier without calibrated wide-format press equipment will produce visible pressure variation across large panels. This is one of the most common quality failures on event branding orders in Kenya.
How to Assess a Sublimation Supplier’s Process Capability
Before placing a bulk sublimation order with any printing company in Kenya, ask these five questions. The answers will tell you whether the supplier is operating a calibrated process or pressing everything at a single default setting.
- What temperature do you press at for this specific fabric? The correct answer names a specific temperature range (e.g. “190–195°C for 100% polyester polo shirts”). A supplier who says “we use the right temperature” or cannot give a number is not calibrating to your substrate.
- What is your dwell time for this order? The correct answer states a time in seconds, adjusted for the fabric weight. “45 seconds for your 180 GSM polo shirts” is a process-controlled answer. “A few seconds” or “until it looks right” is not.
- Do you produce a test press before starting a bulk run? Any reputable sublimation supplier runs a test piece on the actual substrate before committing to a full production run. The test confirms that settings produce the expected colour output on the specific fabric lot in use.
- Can I approve a physical sample before bulk production? A supplier confident in their process capability will offer a physical sample for approval before full production begins. Reluctance to provide samples is a significant risk indicator for bulk orders.
- What is your process for wide-format sublimation (flags, backdrops)? Wide-format sublimation requires different equipment and calibration from small-format garment pressing. A supplier who uses the same heat press for a polo shirt and a 4m teardrop flag does not have the correct equipment for both.
At Waves Branding, our production team answers all five questions for every order before production begins. We operate separate equipment for garment sublimation and wide-format sublimation, run test presses on all new substrate specifications, and provide physical samples for approval on bulk corporate and institutional orders. Speak to our sales team at +254 794 31 44 31 or sales@wavesbranding.co.ke to discuss your order requirements.
For a full overview of our dye sublimation services and products, see our dye sublimation printing service page.
If you are working with cotton or blended fabric and sublimation is not suitable, see our DTF printing service — the recommended alternative for non-polyester fabrics.
For a broader introduction to dye sublimation and why it is used for corporate branding in Kenya, read our guide: Why your business should consider dye sublimation printing in Kenya.
Frequently Asked Questions
What temperature is used for dye sublimation printing in Kenya?
The correct temperature range for dye sublimation printing is 180–200°C, adjusted based on fabric weight and composition. Lightweight flag fabric is pressed at lower temperatures (around 180°C); heavy overalls fabric requires temperatures closer to 200°C for full ink penetration. Waves Branding calibrates press temperature to each substrate type at our Nairobi CBD production facility.
What makes a good dye sublimation printing company in Kenya?
A technically capable dye sublimation company in Kenya should be able to state specific heat press settings for your fabric type, produce a test press before bulk production, offer physical samples for approval, and operate separate equipment for garment and wide-format sublimation. Waves Branding at Keekorok Road, Nairobi CBD meets all of these requirements, with in-house equipment and production team. Contact +254 794 31 44 31 or sales@wavesbranding.co.ke.
What is ghosting in dye sublimation printing?
Ghosting is a faint duplicate image offset from the primary design, caused by the transfer paper shifting during or after pressing before the ink has solidified. It is prevented by maintaining correct pressure throughout the dwell period and by controlled paper removal after cooling. Ghosting cannot be corrected after pressing — it requires a full reprint.
Why do some sublimation prints fade after washing?
Fading after washing is caused by incomplete ink bonding — most commonly from pressing at a temperature below 175°C, or using a dwell time too short for the fabric weight. When the ink does not fully convert to gas and penetrate the fibres, it sits partially on the surface and washes out. Correctly pressed sublimation prints on 100% polyester are wash-permanent.
How do I verify a supplier’s sublimation quality before placing a bulk order in Kenya?
Request a physical sample pressed on the exact fabric and design for your order — not a generic sample from a previous job. Ask the supplier to state the temperature, time, and pressure settings used. Confirm they run a test press before every bulk production run. If a supplier resists any of these requests, treat it as a risk indicator before committing budget to a large order.
